Pro-Tech School of Drywall

Drywall Techniques.com and Pro-Tech School of Drywall offers an intensive 10 week trade course for those who wish to learn the trade and make it their career. Qualified drywallers are in great demand. The training provided with this hands on course, you will be in an excellent position to start your construction career quickly and begin earning good wages! If you want to start your own business, this is an excellent opportunity. In the study of the management and technological aspects of residential and commercial construction projects. Drywall Finishers apply finishing techniques to the planning, design and construction of a project in order to control the time and cost to complete the project and the quality of the construction. The construction industry can use people who possess skills and knowledge in the Pre-Rock Installation, Sheetrock Installation, and Taping & Finishing technological aspects of construction projects.

Drywall is a thin section of gypsum, sandwiched between two pieces of heavy paper used to build inside walls. Drywall Hangers measure, cut and install the drywall whereas drywall finishers, also called drywall tapers cut and install metal corner beads to protect exterior corners, and fill nail indentations, joints, holes and cracks with joint compound. This is accomplished using a taping machine and a broad knife.

Audio, video and multimedia production technology and resources, we provide end-to-end e-Learning content creation solution professionals need a variety of skills to succeed in this dynamic field. If you are looking for a Drywall and a Interior Plaster Restoration school, Drywall Techniques and Pro/Tech School of Drywall provides the comprehensive training and hands-on practice that makes learning of the basics of this field .Drywall was developed as a substitute for wet plaster. It consists of a thin layer of gypsum sandwiched between two pieces of heavy paper made in standard-size panels of four feet by eight or twelve feet. Installers cut the panels to fit, then nail or screw them to the frames.

Drywall installation requires careful measuring and cutting to fit pieces into small spaces above doors or below windows. Installers also saw holes in the panels for electrical outlets and plumbing. Because drywall is heavy, an assistant works with the installer to position and secure the panels. A lift may be used to install ceiling panels. After the drywall has been installed, tapers use a compound to fill joints between panels. Using the tip of a wide trowel, they spread the compound along each side of the joint. They then press a perforated paper tape into the wet compound and scrape away excess material. Tapers, who are also known as finishers, may use automatic taping tools to apply the joint compound and tape in one step. Additional coats may be added to make a smooth surface. Finally, the wall is sanded to ensure uniformity between patched and unpatched areas.

Drywall finisher’s work begins after the drywall has been properly installed by the applicator. They use a special trowel and brush like strokes to fill the joints between the panels. Finishers apply the joint compound along each side of the joint, and apply paper tape over the length of the joint. They immediately use the towel to press the paper tape into the wet compound and remove any excess drywall compound. When the joint compound is dry, they may apply more coats to fill in any holes and make the surface smooth. On bigger projects, drywall finishers might use automatic taping tools that apply the joint compound and tape in one step. They apply two more layers of compound, sanding between each layer. Some finishers may even apply textured surfaces to walls and ceilings with trowels, brushes, or spray guns.

Drywall applicators work in teams, often with other trades people such as carpenters and plumbers. Those who are working on a contract basis.

Plasterers generally work on either interiors or exteriors and apply various types of plasters accordingly. Exterior plasterers apply stucco (a mixture of portland lime, cement and sand) and texture it, or embed it with marble or gravel chips to produce a decorative finish. On interior surfaces, plasterers may use different procedures to apply plaster. They usually put the plaster on walls and ceilings to make surfaces fire resistant or increase soundproofing; however they also apply plaster for aesthetic purposes.

Drywall finishers must have excellent manual dexterity and a steady hand. They are perfectionists, rarely satisfied with their work. They can read blueprints and follow guidelines very easily, yet maintain enough creativity to put their own personal touch into their work. They also enjoy working with people and have great communication skills.

Typical Duties:

• Install metal moldings at the corners of walls
• Tape joints either manually or using an automatic taping tool
• Mix Drywall compounds by hand or with a portable mixer
• Spread and smooth Drywall compound material over taped joints
• Use trowel, broad knife to spread Drywall compound between boards and to fill cracks or holes in the wall and ceiling
• Apply a textured surface and primer to walls and ceilings, to prepare them for painting. Using brushes, roller, or a spray gun
• Sand rough spots of dried Drywall compounds
• Drywall finishers work standard 40-hour weeks, with occasional longer hours to meet construction deadlines. Since they work in buildings that are under construction, they are subject to dust, dirt, loud noises, and bad weather. They may work on ladders and scaffolds and may be required to lift big, heavy sections of drywall. Therefore; they must take proper safety precautions. Most drywall finishers are required to have their own tools, such as a measuring tape and a drywall hammer.

Drywall finishers receive their training either through informal training, on-the-job training or an apprenticeship program. Trade certification can be obtained either through an apprenticeship program or after several years of work experience. While trade certification is not mandatory in all areas to become a drywall finisher, it can be a requirement for many employers and can also help secure employment.

Apprenticeship programs involve a combination of on-the-job training and classroom instruction. A pre-apprenticeship course may also be available which takes about five to six months to complete at a community college and is designed to help you get connected with a good company to apprentice with. It is important to apprentice with a reputable company as that is your education. While some apprenticeship programs may not require a high school diploma, it is important to note that employers generally prefer to hire high school graduates.

Apprenticeships can vary, however a typical apprenticeship lasts four to five years. The apprenticeship is a paid position, however wages are about 50 percent of what an employer pays the Journeyperson, with yearly increases. After successfully completing the apprenticeship requirements, their industry training and apprenticeship office awards the drywall finisher a certificate of completion.

A Union Journeyman in the Seattle Metro area with the full benefit package is about 44 Dollars an hour.

With your tuition paid you will have access to the school for 3 years including any updates that you may inquire about.

There will be an online class for one hour Monday Thru Friday. Students must have Adobe Flashpoint and a web browser to attend classes

Tuitions:

All tuitions will be paid in full via paypal
Students in the United States $2,199.00 for video’s , books ,and instructor
(Optional a Starter Set of Automatic taping and finishing tools $6000.00 dollars Plus Shipping and handling)

International Students Tuition is $4,199.00 for the DVD’s , Books and Instructor. (Optional a Starter Set of Automatic Taping and Finishing tools $6,000.00 Dollars plus International Shipping and handling fees. Additional correspondence fees will be covered under the premium plan)

Students will have the availability of the instructor by phone as well as some of the projects that will be required. You will needed to be video taped and sent to Pro - Tech for grading.

All Students will be able have access to the Instructors and questions answered within 24 hours.